mama Get a free camera plan ☰

Scrap Yard CCTV Specification: Weighment Evidence Chain, Bin Line, Night IR and Storage (India)

By The Mama Editorial Team · Factory-floor cameras, India compliance & operations

In a scrap yard the money question is weighment fraud and segregation leakage, so the camera has to tie each truck's weighbridge ticket to what was loaded from which bin. For a 30×20 m yard with one 16×3 m weighbridge that takes about 9 cameras: four on the weighbridge, two on the bin line, one on segregation and two yard overviews. Plan 125 px/m, the IEC 62676-4:2014 Recognise level (checked 15 Oct 2026), wherever a load has to be recognised.

Last checked: 15 Oct 2026. The yard layout is a worked assumption; densities, lens angles, IR ranges and bitrates are sourced.

Where the rupees go, and which tricks have been caught on weighbridges in India, is in the gate and weighbridge essay. This page is the camera spec that produces the evidence.

Verified against

The weighment evidence chain

A weighbridge ticket carries gross, tare, net and a time, but says nothing about where the load came from or what it was. The chain links each ticket to frames that answer that, one camera view per link.

The links run bin line → segregation bay → plate on the approach → deck side view → load bed end-on → cabin, plus one shared clock: the NVR and the weighbridge PC must show the same time, or the ticket cannot be matched to a frame.

Link What the view proves Level to plan for px/m on target Basis
Bin line Which bin left, how full it was, who loaded it Recognise 125 IEC 62676-4:2014 values
Segregation bay Scrap type went to the right bin Recognise 125 same
Weighbridge approach This ticket belongs to this truck Plate 294–441 Axis LPC white paper, HSRP 340 mm width
Deck, side elevation The weighment was clean: axles on, nobody on the platform Observe to Recognise 62.5–125 IEC 62676-4:2014 values
Load bed, end-on What was weighed, and an empty bed at tare Recognise 125 same
Cabin Who was at the desk when the weight was taken Identify 250 same
Whole yard, day and night Nobody and no vehicle in the yard outside the weighing window Detect, Observe near the cameras 25–62.5 same

Mapping bins, scrap types and load beds to these levels is our assumption; the levels themselves are explained on the DORI page. The plate figure is Axis's "around 100–150 pixels over the full width of the plate" on the 340 mm HSRP width in the Puducherry order. How plate reading behaves on Indian trucks, and how ANPR feeds the gate pass, is on the gate ANPR page.

Clock check at handover (our recommendation): weigh one truck, note the time printed on the ticket, and find that second on all four weighbridge views. If the NVR and the weighbridge PC disagree, set both from the same time source before go-live.

Worked spec for a 30×20 m yard and a 16×3 m weighbridge

Layout assumption: bins along one 30 m wall, a 6 m segregation bay, poles at two opposite corners, and a weighbridge sized like the WBSEDCL pit-less specification (16×3 m, 60 MT, 3 m ramps both sides). Lens angles below are checked against the printed HFOV, not the datasheet's DORI line: CP Plus prints Recognise at 24.8 m for the TA41L6C-Q, while its 49° HFOV gives 23.6 m. Run your own positions in the lens and DORI calculator.

View (cameras) Example camera (datasheet) Pixels × HFOV Mount height, distance (assumed) Scene width (m) px/m achieved Level met IR (datasheet)
Weighbridge approach, plate (1) Prama PT-NC326P1-WNRAM(D2), at tele, 2 MP 1920 × 33.4° 4 m high, 8 m capture (8.9 m slant) 5.4 358 (122 px on a 340 mm plate) Plate 50 m
Weighbridge, side elevation (1) CP Plus CP-UNC-TA41L3C-Q 2688 × 78° 4 m high, 10.5 m from deck centreline (11.2 m slant) 18.2 148 Recognise 30 m
Weighbridge, load bed end-on (1) CP Plus CP-UNC-TA41L6C-Q, 6 mm, 4 MP 2688 × 49° 8 m high, 3 m past the deck end (19.6 m to far bed) 17.9 150 Recognise 60 m
Weighbridge cabin (1) CP Plus CP-UNC-DA41L3C-Q dome, 3.6 mm 2688 × 78° 2 m above the desk, 3 m away 5.8 460 Identify 30 m
Bin line, 30 m (2) Prama PT-NC346P1-WNRAM(D2), 2.7–13.5 mm, set to ~78° 2560 × 78° 6 m high, 11 m out (12.5 m slant) 20.3 126 Recognise 50 m
Segregation bay (1) CP Plus CP-UNC-TA41L3C-Q 2688 × 78° 4 m high, 6 m back (7.2 m slant) 11.7 230 Recognise 30 m
Yard overview, opposite corners (2) CP Plus CP-UNC-TA41L3C-Q, 3.6 mm, 4 MP 2688 × 78° 8 m poles, along the diagonal (36.9 m) 59.8 45 at far corner Detect everywhere; Observe within 26.6 m 30 m

The bin-line camera is a zoom for a reason: at 12.5 m, 125 px/m needs 78.5° or narrower. The Prama PT-NC346P1-WNRAM(D2) zooms from 96.7° to 29.7°; its wide end gives only 91 px/m, so set it near 78°.

Cameras per N metres or per unit (rule of thumb, assumption):

Total for this yard: 9.

Night check: how much of the yard sits inside 30 m of IR

Our grid calculation on this layout: 89% of the yard floor is within 30 m of a corner camera that sees it, and 80% within the 26.6 m Observe distance. The rest is the far edges, beyond the TA41L3C-Q's 30 m IR.

Two ways to close the gap: yard lights over those strips, or a 50–60 m IR model in the corners. On the weighbridge the margin is already there: the plate camera's 50 m IR covers an 8.9 m capture distance, and the end-on view has 60 m IR for a 19.6 m bed.

The 16 m deck and the "4MP only support 0°/180°" gotcha

A 16×3 m deck is long and narrow. Seen side-on, all 16 m fit a 78° lens at about 11 m, which is why the side elevation sits 10.5 m from the centreline. The tempting alternative is a camera along the deck with the image rotated 90° ("corridor" view), so the long deck fills the tall side of the frame.

That is not an option on the 4 MP CP Plus bullets: their sheets say "4MP only support 0°/180°". The TA21L6C-Q supports 90° at 1080p and lower. So choose one: a side-on 4 MP view, or a 2 MP corridor view.

IP, IK, heat and light

Item Scrap-yard spec Source
Ingress IP67 for every outdoor camera; dust and monsoon rain All CP Plus and Prama models above list IP67; test meaning in the IP/IK guide
Impact IK10 within reach of a loader, a magnet crane or thrown scrap Prama PT-NC346P1-WNRAM(D2) and PT-NC326P1-WNRAM(D2): IP67, IK10. Honeywell HC50WB5R2: IK10. CP Plus TC41ZL6C-VMD-LQ: "IK10 (optional)". The TA41L3C-Q and TA41L6C-Q sheets list no IK rating
Operating temperature +60 °C ceiling on every model above CP Plus: −40 to +60 °C (TA41L3C-Q, TA41L6C-Q); Prama: −30 to 60 °C; Honeywell HC50WB5R2: −30 to 60 °C "(IR off)"
Backlight at the gate True WDR in dB for the cabin and side views facing the open yard TC41ZL6C-VMD-LQ lists WDR (120 dB); the TA41L3C-Q lists only DWDR

Every camera here tops out at +60 °C, and one IMD heat-wave criterion is an actual maximum of 45 °C or more, so fit sunshields on poles. Dust and oil mist from turnings film the window and scatter IR; put window cleaning on the yard's routine.

Storage for 30 days

Per the Hikvision recommended-bitrate sheet, H.265 at 25 fps runs at 4,096 Kbps for 4 MP (2688×1520, 2560×1440) and 2,048 Kbps for 1080P; at 15 fps the 4 MP figure is 2,048 Kbps. CP Plus 4 MP models allow 1–25 fps. Bins fill over hours, so the five yard cameras can run at 15 fps (our assumption); keep weighbridge views at 25 fps.

Setting Cameras GB/day 30 days (TB) +30% margin (TB)
All at 25 fps 8 × 4 MP at 4,096 Kbps + 1 × 2 MP at 2,048 376.0 11.3 14.7
Yard at 15 fps 5 × 4 MP at 2,048 + 3 × 4 MP at 4,096 + 1 × 2 MP at 2,048 265.4 8.0 10.4

The sheet advises 20–30% more "if the real environment is more complex", such as swaying tarpaulins. Size the disk with the NVR days table. The boundary wall is a separate zone: see the factory perimeter spec.

When to call the installer / what to ask the vendor

Ask for the printed HFOV at your focal length, the exact model's IK rating, temperature ceiling and image-rotation support, and true WDR in dB. At handover, measure px/m at the far bin and on a plate, by day and at night, and run the clock check on one real weighment.

Mama reads a factory's existing cameras over RTSP/ONVIF and tells the owner, in plain language, how long machines and areas stood idle (askthemama.com). Leave an email or phone in the form below.

FAQ

Can CCTV catch tare-weight tricks at a scrap weighbridge? Partly. The end-on load-bed view shows whether the bed is empty when tare is taken, and the side view shows whether anyone stands on the platform at gross or tare. A camera cannot see a rigged load cell or software; that needs the weighbridge's own verification.

How do I prove which bin a scrap truck was loaded from? Keep a Recognise-level (125 px/m) view on the bin line, read the plate as set out in ANPR for factory gate trucks, and keep the NVR and weighbridge PC on one clock. The ticket time then leads to the plate frame, and the plate leads back to the bin-line frame.

What is the best camera for a scrap yard at night? One with an IR range longer than the distance it must cover, IP67 and, near loaders, IK10. In this layout two 30 m IR corner cameras reach 89% of the yard; the bin-line camera has 50 m IR against a 12.5 m distance.

Last verified 15 Oct 2026 against the vendor and regulator documents listed above. Found an error? Tell Mama in the form below.

Read next
Free · no obligation

Get a camera plan for your floor

Tell Mama about your plant and Mama will come back with how many cameras you need, where they go, and the retention your state expects — sized to your floor, in ₹. Built for Indian factories.

  • How many cameras & exact placement
  • Compliance-ready (BIS/STQC, women's night shift)
  • Honest ₹ estimate — guard vs camera-AI

Mama replies by email or phone — whichever you left. No spam, no obligation.